Brick Paver Installation & Edging



Staging of material

Many paver tasks will vary depending on gain access to, website conditions, project size and of course, the weather condition. Mindful consideration needs to be taken to determine the time to begin the paver installation.

The foreman or job supervisor ought to constantly have the materials (sand/ pavers) dispersed around the task site for effective and easy setups. Paver pallets/bundles should be put in a way not to interfere with the paver installation. The correct pallet/bundle placement can make the actual job installation much easier and quicker by decreasing the general labor of dealing with the product.

Brick paver patterns

Pavers can be put in several patterns depending on their shape. Each paver shape will normally have numerous different hatch patterns that are supplied by the maker.

Contractors require to take into factor to consider the traffic weight loads on their paver projects. In a lot of applications around the world, it has been shown that pavers laid in a herringbone pattern have actually carried out adequately.

Pavers that are 60 mm (2 - 3/8 in) thickness appropriate for pedestrian applications. Pavers that are going to be utilized in industrial or commercial applications need to be 80 mm (3 - 1/8 in) in thickness.

Reference/starting point for brick paver installation

There are a number of conditions that identify the beginning point of a paver task.

When starting to install pavers it is best to snap a true straight chalk line on the surface of the bed linen sand or pull a real straight string line above the surface of the bedding sand at the finished elevation of the pavers This will help as a guide for preserving straight joint lines and will likewise permit the installer to make adjustments in the alignment of the pavers.

Buildings and concrete suppressing are usually not straight and need to not be used for establishing straight joint lines. Using string lines is vital to figure out the true straightness of the edge as well. As the paver installation progresses, the string lines will help decrease the requirement for little trim pieces.

Joint width in between pavers need to be between 1/16 and 3/16 in (2 and 5 mm ). There are some pavers with spacer bars on their sides. These will preserve a minimum joint width and enable the bed linen and jointing sand to get in between each paver. Pavers with spacer bars are usually not laid in snug versus each other since a string line will offer consistent joint spacing.

Installation of brick pavers.

One of the most widely used techniques for the installation of pavers is hand installation of each paver. It is best to set up a single row of pavers along one of the real straight lines that you have pulled or above the bedding sand. The best method is to position a paver versus another one and let it move down into the bedding sand.

When setting up pavers on a high grade, they need to be set up at the base of the grade going uphill. This will avoid the pavers from creeping as they are being laid.

On large commercial and commercial applications, hand laying pavers would not be cost effective due to the labor intensity. The very best method for setting up pavers on large projects is to install them mechanically. Using a mechanical laying machine can install roughly 6000 - 7000 sq ft a day. There are a couple products a contractor must consider prior to setting up pavers mechanically:

1.) Mechanical installers are just capable of installing pavers in particular patterns.

2.) The specialist must make sure that the producer is capable of manufacturing and bundling pavers in the wanted pattern on the pallets for simple mechanical installation.

Poor color blending might result in a patchy looking installation. A lot of manufacturers are consistent with color mixing on each package of pavers, but it is the professional's duty to make sure proper mixing in the field.

Cutting treatments for brick pavers.

Specialists usually have 2 methods of cutting pavers. Pavers are cut either by 1). A double bladed guillotine or by 2). A gas powered cut off saw or brick saw which is geared up with a diamond blade. The diamond blade cut-off saw or brick saw will provide a much cleaner and more accurate cut. Many brick saws will have a pipe accessory on them which will allow the operator to cut the pavers wet. When cutting pavers wet, it will help reduce dust and will lengthen the diamond blades life also. The operator of the brick saw ought to always cut the pavers away from the surface of the paver field when cutting damp, due to that the pavers will create a slurry that will stain the paver surface area. Pavers that are cut must not fit tight, adequate spacing ought to be available for jointing sand.

The brick saw operator ought to always use the appropriate defense that is required for running a saw, such as eye, ear, respiratory and hand defense ).

Edging types

Edge restraints play a significant function in the total success of an interlocking pavement installation Edging restraints eliminate lateral motion of the pavers and hold the pavers firmly together. Particularly at the outer boundary of the paver application, without an edging restraint, your project is guaranteed to stop working with time.

Usually produced edge restraints are the most commonly utilized by specialists. Produced edging restraints can range from, plastic edging, steel and aluminum, lumbers or precast concrete and stone.

Edging installation.

This might result in the migration of the bedding sand and ultimate lateral motion of the pavers. If there is a possibility of losing bedding sand in between the pavers and the edge restraint, then geo textile fabric is suggested. When a gap in between the pavers and the edging exceeds 3/8" (10mm), then the area ought to be filled with cut pavers.

Compaction of brick pavers.

After installation, the pavers have to be compacted. The whole area that is to be compressed should be swept tidy of any foreign objects and particles that can cause scratching or scuffing on the surface of the pavers.

It is essential to have a compactor that can put in in between 3000lbs. And 5000 lbs. Of centrifugal compaction force. In addition, it is important that the first compaction happens before any jointing sand has actually been applied to the pavers. If jointing sand is applied to the pavers prior to compaction takes place, this can cause a bridging issue and will not enable the joints to be entirely filled with jointing sand. This can also avoid the pavers from being correctly set into the bed linen sand.

When compacting the pavers, it is suggested that you make at least two passes in different instructions throughout the pavers. This will allow the pavers to be properly embeded in the bedding sand and will force the bed linen sand up into the joints from the bottom of the pavers.

The compaction of the pavers is extremely vital to the final Koi Pond Florida performance of the pavers. Failure to do correct compaction can result in contortions and pavement failure with time.


Paver pallets/bundles need to be positioned in a manner not to interfere with the paver installation. One of the most commonly used methods for the installation of pavers is hand installation of each paver. The operator of the brick saw ought to always cut the pavers away from the surface of the paver field when cutting damp, due to the truth that the pavers will create a slurry that will stain the paver surface. Edging restraints remove lateral motion of the pavers and hold the pavers firmly together. When a gap in between the pavers and the edging surpasses 3/8" (10mm), then the space must be filled with cut pavers.

Leave a Reply

Your email address will not be published. Required fields are marked *